Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
Jump to Subcategory:
added to your cart!
Metal Hex Male/Female standoffs. #4-40 thread with 3/8" shank and 3/16" thread length. Can be stacked to create any length. …
There are your standard Philips-head 4-40 screws. They are 1/4" long and come in packs of ten. This is the screw size we use …
These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or …
We could talk about how the Zinc used in these nuts is only from the finest old-growth Zinc trees from across the globe and i…
These nylon standoffs are 3/4" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or …
These are very handy. They are simple angle brackets with one threaded and unthreaded hole. Use them for connecting PCBs at 9…
Standard Philips-head 4-40 screws. They are 1/2" long and come in packs of ten. This is the screw size we use in most of the …
Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floating …
Metal short standoffs: 3/8" long x 1/4"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development …
"Rubber" feet raise your PCB or project up off your desk.
A 5-pack of the M.2 screws that SparkFun uses with the MicroMod ecosystem.
These are Philips-head M3 screws. They are 12mm long and come in packs of three. This is the screw size that the MiP robotic …
These stainless steel shaft couplers allow you to couple two size shafts together. They can be used for connecting motor shaf…
**Description**: These are standard nuts with 2-56 thread. For use with 2-56 machine screws and five button pad set listed be…
Standard Philips-head 4-40 screws. They are 3/4" long and come in packs of ten. This is the screw size we use in most of the …
This hardware kit consists of four each of M2 style nylon hex nuts and screws.
These are standard screws with 2-56 thread and 3/8" long, recommended for the small button pad sets. Can be used with a 2-56 …
These 10" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06".…
This is a M3 - 0.5x10mm Phillips Head Machine Screw.
These dolly wheel drive plates provide you with a way to create an easy to assemble, low friction, drive system. The idler A …
These 2" long aluminum tubes have an outer diameter of 1", an inner diameter of 0.82", and a wall thickness of 0.09". When us…
These 8" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". …
These plastic shaft spacers have an inner diameter of 5/8” and a thickness of 1/16”. These spacers are ideal for spacing …
This is a M3 - 0.5x30mm Phillips Head Machine Screw.
**Replacement:**[PRT-10927](http://www.sparkfun.com/products/10927). These are now sold in packs of ten! This page is for ref…
These dolly wheel drive plates provide you with a way to create an easy to assemble, low friction, drive system or motorized …
These 10" long aluminum tubes have an outer diameter of 3/8", an inner diameter of 0.30", and a wall thickness of 0.035". Whe…
These plastic shaft spacers have an inner diameter of 1/2” and a thickness of 1/16”. These spacers are ideal for spacing …
These center hole adaptors come in packs of four, are .08” thick, and have an outer diameter .54”. Their ½” diameter l…
These 10" long aluminum tubes have an outer diameter of 5/8", an inner diameter of 0.569", and a wall thickness of 0.028". Wh…
This is an M3 Hex nut for use with M3 screws.
This is a 4-40, 1in. Phillips head screw.
